Does OSHA 30 expire? No. The OSHA 30-hour Department of Labor card does not expire, and the Occupational Safety and Health Administration (OSHA) has never set a federal renewal interval for it. There is no expiration date printed on the card because there is no expiration to print.
That is the accurate answer, and it is close to useless at a badging trailer.
A worker gets turned away at a gate somewhere in the country every morning holding a perfectly valid card from 2018, because the general contractor’s prequalification packet says five years and the badging clerk is not empowered to argue about federal rulemaking. Both things are true at once: the card is permanent, and the card is routinely treated as though it is not.
Understanding the gap between those two facts is what actually keeps your crews working.
Where the five-year rule came from
Almost everyone who believes OSHA 30 expires after five years is half-remembering a real rule that says something else entirely.
The OSHA Outreach Training Program allows a student who lost a card to request a replacement, and that replacement is available through the authorized trainer or the OSHA Training Institute Education Center that issued it for five years from the course completion date. Past five years, the trainer cannot pull the record and reissue. The student has to sit the course again.
So the five-year number is real. It attaches to the paperwork, not the training. Your card is still valid at year six; you simply cannot get a duplicate of it if you lose it. Somewhere along the line that turned into “OSHA 30 expires every five years,” and it has been repeated by enough training brokers and enough prequalification forms that the distinction stopped mattering in practice.
The other half of the myth comes from a genuine coincidence: five years is also the interval most large contractors and owners chose when they wrote their own refresh policies. When a rule and a myth land on the same number, the myth wins.
What the card actually is
The Outreach card is documentation that a person attended an orientation-level course taught by an OSHA-authorized trainer. That is the whole of it. It does not qualify anyone to perform any specific task.
It is also not something an employer is federally required to obtain. OSHA Outreach training is a voluntary program. No federal construction or general industry standard says “employees shall hold a 10-hour card.” The card became near-universal because contracts, states, and owners made it a condition of entry, not because OSHA mandated it.
The 10-hour class is the usual choice for entry level workers, and the 30-hour class is meant for workers with some safety responsibilities. Neither card carries a federal expiration date.
Many general contractors and owners still require OSHA 10 or 30 cards, and some ask for refresher training every few years. Workers who complete the OSHA 30-hour training course keep the same card. A new OSHA 30 training class only answers that contract rule, not a federal one.
What the card does well is establish a shared baseline. Everyone on the site has heard the same overview of the same hazard categories from someone the agency authorized to teach it. What it does not do is satisfy any standard-specific training requirement. A worker with a fresh 30-hour construction card and no fall protection training is an untrained worker under the fall protection standard. The card does not close that gap and was never designed to.
The card comes from the Education Center, not from your trainer
This trips up employers who expect to walk out of class with cards in hand. The authorized trainer teaches the course and submits the roster and documentation to an OSHA Training Institute Education Center. The Education Center processes the cards and the trainer gets them to the students. That takes weeks, not days.
What the trainer can hand you at the end of class is a course completion certificate. That is a useful bridge document while the card is in process, but it is not the card, and whether it is accepted is up to the organization asking for it. If you have a mobilization date, work backward from it. Scheduling OSHA 30-hour construction the week before a crew is due at a gate is how people end up standing in a parking lot.
One more program rule that surprises schedulers: Outreach training is capped at a limited number of instructional hours per day — seven and a half — which is why a legitimate 30-hour course cannot be compressed into two very long days. Anyone offering to do that is offering you a card that will not survive an audit of the training records.
Does OSHA 10 expire?
No. The same answer applies: the OSHA 10-hour card carries no federal expiration date, and OSHA has set no renewal interval for it. How long is OSHA 10 good for depends on who is asking, because a general contractor, an owner, or a state can set its own refresh rule. The five-year limit on getting a replacement card applies to the 10-hour course as well.
How long is OSHA 30 good for, and who puts a clock on it?
OSHA does not. Four other parties routinely do, and every one of them can shut a worker out of a job.
General contractors and construction managers. The prequalification packet is where most refresh rules live. Three years and five years are both common. Some owners write “current within five years” and some write “within five years of the badge date,” which are different rules that produce different answers for a card issued four years and eleven months ago.
Facility and plant owners. Industrial owners with contractor safety programs often set their own interval and will not badge a contractor employee whose card falls outside it. Refineries, chemical plants, food and pharmaceutical facilities are the most consistent about this.
States and municipalities. Several states require the 10-hour card on public works projects, usually within a set number of days after hire. At least one state ties its construction training requirement to whether the course was completed within the previous five years, which makes the card functionally expiring in that jurisdiction.
New York City’s site safety training rules run on a separate card entirely, with its own renewal cycle, and the Outreach hours feed into it rather than replacing it.
Insurers and unions. Carriers writing contractor policies and joint labor-management programs both set training expectations, and both tend to prefer a stated interval over “never.”
None of these is OSHA. All of them are enforceable against you in ways OSHA is not, because losing a badge costs you the job the same week rather than a citation months later.
The badging desk is the real enforcement point
Compliance officers rarely ask to see Outreach cards. They ask for the training records that the standards actually require — who was trained on what hazard, by whom, on what date, and how competence was verified.
Badging clerks ask for the card every time. That inversion is worth sitting with, because it explains why so much employer energy goes into a document OSHA never required and so little goes into the documentation OSHA reads. The card gets your people through the gate. The standard-specific training records are what defend you after something happens.
A mature program funds both and does not confuse them.
Does OSHA 30 expire? No, but this training genuinely does
Here is the distinction that matters more than anything else in this article. The Outreach card carries no interval. A significant amount of the training your crews need carries a real one, written into a standard or a consensus document, and those are the intervals that produce citations when they slip.
| Training | What sets the interval | Interval |
|---|---|---|
| OSHA 10 / 30 Outreach card | OSHA Outreach Training Program | None. Card is permanent; replacement available from the trainer for five years |
| Powered industrial truck operator | 1910.178(l)(4)(iii) | Performance evaluation at least once every three years, plus refresher on trigger |
| HAZWOPER general site worker | 1910.120(e)(8) | Eight hours of refresher annually |
| Bloodborne pathogens | 1910.1030(g)(2)(ii) | At initial assignment and at least annually thereafter |
| Respiratory protection | 1910.134 | Annual retraining and annual fit testing |
| Arc flash and electrical safe work practices | NFPA 70E | Retraining at intervals not to exceed three years, plus event triggers |
| Lockout/tagout | 1910.147 | No fixed training interval; annual periodic inspection of procedures; retraining on trigger |
| Fall protection, construction | 1926.503(c) | No interval; retraining when the employer has reason to believe understanding lapsed |
| Hazard communication | 1910.1200(h) | At initial assignment and whenever a new chemical hazard is introduced |
| First aid, CPR, AED | The certifying organization, not OSHA | Commonly a two-year certification cycle |
| Aerial and scissor lift | ANSI A92 series and employer policy | Retraining on trigger; many employers adopt a three-year cycle by policy |
Read that table next to your training matrix and the priorities usually reorder themselves. The company chasing five-year OSHA 30 refreshes while its forklift operator evaluations are four years stale has the sequence backward. So does the one tracking Outreach cards on a spreadsheet while nobody owns the HAZWOPER annual refresher or the respiratory protection retraining and fit test calendar.
Trigger-based retraining does not wait for an anniversary
Several standards in that table have no calendar interval at all, and employers read that as “no requirement.” It is the opposite. Trigger-based retraining is harder to manage than an annual cycle, because the trigger arrives on its own schedule.
The triggers repeat across standards with very little variation: the job assignment changes, the equipment changes, the process changes, a new hazard appears, an inspection or observation reveals that someone is not following the procedure, or something goes wrong. Any of those obligates retraining under the standard that governs the task.
In practice this is where energy control training and fall protection training quietly fall out of compliance. Nothing on the calendar came due. A machine got replaced, or a crew started working off a different edge, and nobody treated that as the training event it legally was.
There is no OSHA 30 refresher course
People ask for one constantly. It does not exist in the Outreach program. A worker with a 10-hour card who needs a 30 normally takes the full 30-hour course. The one exception is a 20-hour follow-on from the same trainer, finished within 180 calendar days of the start of the 10-hour class, with the 10-hour card turned in.
If a general contractor requires a card issued within the last five years and your foreman’s card is six years old, the only path is the complete course again. That is thirty hours off the tools. Budget it as such, and stop hoping a four-hour refresher will satisfy anyone.
The upside is that the second pass is not wasted. Standards move, the Focus Four emphasis shifts, and a supervisor who took OSHA 30-hour general industry in 2017 genuinely has not heard the current material. Companies that treat the retake as an imposition get an imposition. Companies that treat it as the one guaranteed touchpoint with their supervisors every few years get something out of it.
Construction or general industry — the mismatch that stops people at the gate
The second most common badging rejection has nothing to do with dates. It is a worker holding a general industry card at a construction site, or the reverse.
These are two separate curricula built on two separate parts of the regulations. The construction card is grounded in the 1926 standards and spends its time on falls, struck-by, caught-between and electrocution, plus excavation, scaffolds and the rest of the construction hazard set.
The general industry card is grounded in 1910 and covers machine guarding, walking-working surfaces, energy control, hazard communication, PPE and industrial exposures. A card in one does not substitute for the other, and there is no conversion.
Get the determination right before you buy the class. Maintenance and plant crews generally need general industry. Trades doing construction, alteration or repair generally need construction. Companies that do both often need both, and a supervisor who moves between a plant and a construction project may legitimately need to hold two cards.
If your workforce is mixed, sort that out before scheduling — a wrong-curriculum class is not a partial win, it is a full retake. Working through the full course list against your actual scopes of work takes an hour and saves a mobilization.
What happens when a card is lost
Cards get lost constantly. They live in wallets, they go through washing machines, and they disappear when someone changes employers.
Inside the five-year window, the replacement path runs back through the authorized trainer or the Education Center that issued the card. The student needs to know roughly when and where the class was taken and who taught it. That is exactly the information nobody has, which is why the employer’s copy of the roster is worth more than the card itself.
Outside the five-year window, there is no replacement. The record cannot be reissued and the worker retakes the course. This is the single strongest practical argument for the discipline in the next section, and it costs nothing to implement.
How to verify a card you did not issue
Fraudulent Outreach cards are sold openly online, and they are good enough to pass a glance at a gate. If you are hiring a foreman who says he holds a 30-hour card, a photograph of the card is weak evidence.
There is no single public national database an employer can search to confirm a card. Verification runs back through the trainer or the Education Center that issued it. Ask for the trainer’s name and the course dates, not just the card number, and treat a candidate who cannot produce either as someone whose card you have not verified.
The tells on a fake are usually mundane: a card that arrived the same day the class supposedly ended, a 30-hour course completed in a weekend, or a card with no traceable trainer. None of those is proof by itself. All of them are worth a question.
What to put in your written policy
Because OSHA gives you no interval, you have to choose one and write it down. A policy that says nothing leaves every decision to whoever is standing at the gate that morning.
- Pick an interval and say why. Five years is the common default because it matches the replacement window and most contractor prequalification forms. Three years is defensible where your customers demand it. Choosing deliberately is what matters; drifting is what gets you caught short.
- Name the card type by role. Which positions need construction, which need general industry, which need 10 versus 30. Write it into the job description so hiring does not have to re-decide it.
- Keep the roster, not just the card. Scan the card and keep the class roster, trainer name and course dates in the employee file the day the class ends. That single habit makes replacements possible and verification trivial.
- Track the expiring training separately. Outreach cards and interval-bound training belong on different tracks, because one is a customer requirement and the other is a citation exposure. Do not let one calendar hide the other.
- Set a lead time. Flag cards at twelve months out, not thirty days. A 30-hour course is a week of a supervisor’s time, and it will not fit into a schedule you built last Friday.
- Decide who pays and who sits. New hires arriving with old cards are a recurring cost. Companies that have not decided in advance make the decision badly under deadline pressure.
How to run a refresh cycle without shutting the job down
The scheduling problem is real. Thirty hours is a full week for one person, and if your policy comes due for a dozen supervisors in the same quarter you have a staffing problem rather than a training problem.
Three things help. Stagger the cohort deliberately when you first set the policy, so the whole crew does not come due at once. Run the class on your site rather than sending people out, which removes travel and lets you use your own equipment and your own incidents as examples. And bundle it — if you are already bringing a trainer in for a week, the marginal cost of adding a day of competent person training or an arc flash and NFPA 70E session is much lower than a separate engagement.
Cost on this work is driven by crew size, the number of days on site, travel to your location, and how many separate courses you stack into one visit. It is not driven by the card. Two companies with identical headcounts can pay very different amounts depending on how well they sequenced the year.
The mistakes we see most
- Treating the card as compliance. The 30-hour course is an overview. It does not qualify anyone as a competent person, does not satisfy a standard-specific training requirement, and does not authorize anyone to operate equipment.
- Buying the card, not the training. Programs that exist to produce a card in the shortest legal time produce workers who remember nothing. That shows up in behavior long before it shows up in an audit.
- No record of the class. The training happened, the roster went nowhere, and five years later nobody can replace a lost card or prove the class occurred.
- Wrong curriculum. A general industry card bought for a construction crew because it was scheduled sooner.
- Assuming the interval is federal. Employers cite “OSHA requires renewal every five years” in their own written policies. It reads as competence to nobody who knows the program, and it makes the rest of the policy suspect.
- Ignoring the trigger-based standards. The calendar looked clean because the only tracked item was a card that never comes due.
Common questions
Does OSHA 30 expire?
No. The Department of Labor 30-hour Outreach card does not expire and OSHA sets no federal renewal interval for it. What does have a limit is card replacement — the trainer or Education Center can reissue a lost card for five years from the course date, after which the course must be retaken. Separately, many general contractors, owners and a few states require a card issued within the last three to five years as a condition of site access, and those requirements are enforceable against you even though OSHA’s is not.
Do I need to renew my OSHA 30 card every five years?
Not under federal OSHA. Check the contract, the site’s badging requirements and the state you are working in, because that is where a five-year rule actually lives. If your work is concentrated with owners who impose one, write the same interval into your own policy so you are never surprised at a gate.
Is there an OSHA 30 refresher course?
No. The Outreach program has no refresher. If a customer requires a more recent card, the worker retakes the full 30-hour course.
Can I get a replacement OSHA 30 card?
Yes, within five years of the class, through the authorized trainer or the OSHA Training Institute Education Center that issued it. You will need the course dates and the trainer’s name, which is why the employer should keep the roster rather than relying on the worker’s wallet.
Does an OSHA 30 card make someone a competent person?
No. A competent person is designated by the employer based on the ability to identify hazards and the authority to correct them, and the designation is task-specific. The Outreach card is orientation-level awareness training and does not establish either element.
Does OSHA require the 10-hour or 30-hour card at all?
Not federally. Outreach is a voluntary program. The card became a de facto requirement through contracts, owner policies and a handful of state laws covering public works, not through a federal standard.
Sort the permanent from the perishable
The practical move is to split your training register in two. On one side, the Outreach cards — permanent under federal law, governed by whatever interval your customers impose, and worth tracking against the five-year replacement window regardless. On the other side, the training with real intervals and real triggers, which is what a compliance officer will ask about and what your incident record depends on.
Most companies that ask us whether OSHA 30 expires discover in the same conversation that two or three genuinely expiring items have gone quiet. If you want a read on where you stand, tell us what your crews do and what your customers require and we will map it against the standards that attach. We run training at your site across the country, and you can see where we work on the locations page.
About the Author
Patrick Salazar — founder of 3P Safety and an OSHA 500 authorized construction outreach trainer, working NCCCO-certified mobile crane operator (LBC, TLL, TSS), tower crane operator, certified crane inspector, and lift director. In the field since 2005, delivering instructor-led safety training at jobsites and facilities nationwide. General Industry outreach courses are taught by our team's OSHA 501 authorized trainer.

